maxpromer

#include <ACAN2517FD.h>
#include <SPI.h>

// Configs Pin
static const int CAN_CONTROLLER_SCK  = 18;
static const int CAN_CONTROLLER_MOSI = 23;
static const int CAN_CONTROLLER_MISO = 19;
static const int CAN_CONTROLLER_CS   = 5;
static const int CAN_CONTROLLER_INT  = 15;

maxpromer

#include <ACAN2517FD.h>
#include <SPI.h>

// Configs Pin
static const int CAN_CONTROLLER_SCK  = 18;
static const int CAN_CONTROLLER_MOSI = 23;
static const int CAN_CONTROLLER_MISO = 19;
static const int CAN_CONTROLLER_CS   = 5;
static const int CAN_CONTROLLER_INT  = 15;

maxpromer

#include <Arduino.h>
#include <WiFi.h>
#include <WiFiClientSecure.h>
#include <DuinoClaw.h>

// Built-in tools
#include <Tools/GetCurrentTimeTool.h>
#include <Tools/GPIOTool.h>
#include <Tools/WiFiTool.h>

maxpromer

void setup() {
  Serial.begin(115200);
  Serial2.begin(9600, SERIAL_8N1, 4, -1); // RX pin=4, TX pin=no connect
}

void loop() {
  int c = Serial2.read(); // Read data from GM65
  if (c >= 0) { // if can be read
    Serial.write((char) c); // send it to Serial Monitor
  } else {

maxpromer

#include <Arduino.h>
#include <Wire.h>
#include <IOXESP32_4-20mA_Receiver.h>

Receiver4_20 sensor(&Wire, 0x45); // Default 0x45

const int raw_in_0cm = 6485; // Enter Raw value in level 0CM 
const int raw_in_20cm = 7521; // Enter Raw value in level 20CM 

void setup() {

maxpromer

/* ----------------------------------------------------------------------
"Simple" Protomatter library example sketch (once you get past all
the various pin configurations at the top, and all the comments).
Shows basic use of Adafruit_Protomatter library with different devices.

This example is written for a 64x32 matrix but can be adapted to others.

Once the RGB matrix is initialized, most functions of the Adafruit_GFX
library are available for drawing -- code from other projects that use
LCDs or OLEDs can be easily adapted, or may be insightful for reference.

maxpromer

#include <Adafruit_Protomatter.h>
#include <Wire.h>
#include <ArtronShop_SHT3x.h>

uint8_t rgbPins[]  = {42, 41, 40, 39, 38, 37}; // R1, G1, B1, R2, G2, B2
uint8_t addrPins[] = {48, 36, 45, 35}; // A, B, C, D
uint8_t clockPin   = 2;  // CLK
uint8_t latchPin   = 47; // LAT
uint8_t oePin      = 14; // OE

maxpromer

#include <Adafruit_Protomatter.h>
#include <WiFi.h>
#include <WiFiMulti.h>
#include "time.h"

uint8_t rgbPins[]  = {42, 41, 40, 39, 38, 37}; // R1, G1, B1, R2, G2, B2
uint8_t addrPins[] = {48, 36, 45, 35}; // A, B, C, D
uint8_t clockPin   = 2;  // CLK
uint8_t latchPin   = 47; // LAT
uint8_t oePin      = 14; // OE

maxpromer

#include <driver/i2s.h>
#include <math.h>

// ─── กำหนดขา I2S ───────────────────────────────────────
#define I2S_BCK_PIN   26   // Bit Clock
#define I2S_WS_PIN    25   // Word Select (LRCK)
#define I2S_DATA_PIN  22   // Data Out → DIN ของโมดูล

// ─── พารามิเตอร์เสียง ────────────────────────────────────
#define SAMPLE_RATE   44100

maxpromer

#include "Arduino.h"
#include "WiFi.h"
#include "Audio.h"

// ─── กำหนดขา I2S ───────────────────────────────────────
#define I2S_BCK_PIN   26
#define I2S_WS_PIN    25
#define I2S_DATA_PIN  22

// ─── ข้อมูล Wi-Fi ────────────────────────────────────────